Prev

Next

The detailed difference between 4G industrial router...   4G industrial router and 4G DTU both realize the wireless network data transmission function, and the differences between them are mainly from the use method, appearance interface and application environment, etc. Today, we will introduce some differences between 4G router and 4G DTU.   Different methods...

更多文章

Application analysis of iot sensing technology   The Internet of things (iot) is widely used in the integration of networks through intelligent perception, recognition technology, pervasive computing and other communication perception technologies. The iot is understood as "Internet connected by things". The Internet of things (iot) connects all objects with...

更多文章

What is a single/dual frequency wireless 4G router 1. Introduction to "single frequency" router The single-frequency router only works in the 2.4ghz band, which is generally supported by wireless terminals. However, the 2.4ghz band has large interference, which may affect the wireless rate and stability.   2. Introduction to "dual-frequency" router Dual-frequency...

更多文章

Wireless communication DTU features Data Transfer unit (DTU) is a wireless terminal device specially used to convert serial Data into IP Data or convert IP Data into serial Data for transmission through wireless communication network.   DTU advantages: Rapid and flexible network, short construction cycle, low cost; Wide network coverage; Good...

更多文章

The advantage of using wireless data transmission module... Data transmission can be simply divided into two major types: wired (including the installation of optical cables, cables or leased telecommunication lines) and wireless (including the establishment of dedicated wireless data transmission system or the borrowing of CDPD, GSM, CDMA and other public network information platforms).     In...

更多文章

twitter

工业路由器NBMA网络转化为点到点的链路

Category : 产品文章

当我们使用点到点子接口将NBMA网络转化为点到点的链路时,整个NBMA网络将产生过多的PVC部分互联或全互联的网状结构,但这将产生一定的负面影响,会使网络中产生大量的LSP泛洪流量。我们都知道,运行IS-IS的工业路由器当接收到一个LSP报文后,会将此LSP从除接收接口以外的所有启用了IS-IS协议的接口泛洪出去,以使网络中的其他工业路由器都可以接收到此LSP。但是这种泛洪机制对于存在大量部分互联或全互联的网络将产生过多冗余的LSP扩散。

所谓全互联或全网状网络拓扑,是指所有工业路由器都与其他工业级无线路由器向连接(通常是点到点子接口)。在这样的一个网络中,当一台路由器从某接口收到邻居泛洪过来的LSP后,由于它并不知道这个LSP是否已经被其他邻居工业4g路由器收到,所以会再从其他接口泛洪出去,即使其他工业级4g路由器的链路状态数据库中已经存在这个LSP。如果网络中有n个全网路由器的话,那么网络中的每台工业级LTE路由器都会扩散n-2条冗余的LSP,这样总共被泛洪的多余的LSP将为(n-1)x(n-2),条而这些LSP的扩散是多余。如果每台工业全网通路由器都刷新一条LSP的话,那么这个数量还将会成倍数的增长,导致了大量带宽资源的浪费。

为了解这种在全互联或高度互联的网络中出现的LSP泛洪的冗余现象,IS-IS提供了一种解决方案——IS-IS全通组,也称作Mesh组。IS-IS全通组在RFC2973中进行了定义。所谓全通组,就是假设所有工业3G路由器之间都是完全互联的,每个工业级全网通路由器都会直接收到其他全网通工业级路由器泛洪的原始的LSP的拷贝。

可以将全网工业路由器的接口加入到某个全通组中,一个全网通工业路由器上可以存在多个全通组,全通组内接口之间的LSP泛洪是受限制的,全通组之间的LSP泛洪是正常的操作,未加入全通组的工业级3G路由器接口与全通组之间也是正常的LSP泛洪操作。全网通路由器  无线路由器